EAPL

Features :

• Din sized enclosure for Track (Din rail) / Screw mounting.
• Front terminal protective cover for safety.
• LED indication for timing in progress.
• A1DA :External (zero volt / potential free) command contact for timing initiation.

Applications : AMF panels, Automation panels, HT / LT panels, MCC panels, C & R panels, RTCC panels, Transformer panels and many more,

Dimensions : Over-all: 22.5 X 75 X 102mm (W X H X D).

Features :

• Din sized enclosure for Track (Din rail) / Screw mounting.
• B1DCA-T : HOLD / RESTART facility during power fail conditions.
• B1DCA-T : Auto / Manual switch for mode of operation
• B1DCA-T : Program - enable / disable facility for tamper proof operation.
• B1DCA-X, B1DCA-T : Independently selectable ON & OFF time.
• SPP-T :Trips under phase missing, phase reversal or phase unbalance
• In manual mode, terminals provided to connect to switch so as to manually switch ON and switch OFF load

Applications : Lubricating system, DG Sets, MCC panels, Pump panels and many more.

Dimensions : Over-all: 45 X 75 X 116mm (W X H X D).

Features :

• Slim and Compact design
• Suitable for Din Rail Mounting
• Finger guard protection.
• LED indication for timing in progress

Dimensions : Over-All 22.5 x 75 x 102 mm (W X H X D)

Applications : Automation Panels, HT / LT Panels, MCC Panels, C & R Panels, RTCC Panels, Transformer Panels and many more.

Features :

• Slim and Compact design
• Suitable for Din Rail Mounting
• Finger guard protection
• LED indication for timing in progress

Dimensions : 17.5 x 89.0x 62.0mm (W x H x D)

Applications : Automation Panels, HT / LT Panels, MCC Panels, C & R Panels, RTCC Panels, Transformer Panels and many more.

Features :

• Slim and Compact design
• Suitable for Din Rail Mounting
• Finger guard protection
• LED indication for timing in progress

Dimensions : 17.5 x 89.0x 62.0mm (W x H x D)

Applications : Automation Panels, HT / LT Panels, MCC Panels, C & R Panels, RTCC Panels, Transformer Panels and many more.

Features :

• Din Sized enclosure for panel mounting.
• Digital dual display for set value and process value.
• FUNCTION (programmable): ON DELAY / INTERVAL /CYCLIC ADJUSTABLE.
• TYPE OF START SIGNAL (programable) : NO START / PULSE / CONTINUOUS.
• One of the relay c/o can be configured as INSTANT or DELAYED.
• Program lock is provided for function, relay configuration, type of start signal and range selected.
• RESET cum START facility can be achieved either through front buttons Or Rear terminals
• HOLD/RESTART facility during power failure conditions.
• Internal Resettable fuse for protection of device against voltage fluctuations(N.A. for H3PT-MU). Digital display will blink whenever voltage exceeds specified voltage range. Switch off the unit for sometime & then switch on when voltage returns to normal

Dimensions :

• Over-all: H3PT-MU – 48 x 48 x 95.5mm, C3PT-MU , E3PT-MU – 96 x 96 x 117mm (W x H X D)
• Cut-out: H3PT-MU – 46 x 46 mm, C3PT-MU, E3PT-MU – 92 x 92mm (W x H)

Applications
Injection moulding machine panels, Granite processing machines, Packaging / Printing machines, Hot stamping machines etc.

Features :

• Suitable for screw mounting(except ST4-M1).
• 7 segment display indication for channel and timing operation (except ST-4M1).
• User friendly programming for ON/OFF time selection independently (except ST-4M1).
• Hold /Restart feature is available during power failure, Over voltage protection(except ST-4M1).
• ST-6M1 / ST-10M2 / ST-10M1 : pulse start signal.
• ST-15M2 / ST-4M1 : continuous start signal.
• S1D-C8M3 : Comprises of 8 Relays and each relay can be programmed for maximum of 8 switchings in a cycle.
• Potential free (Zero volts) continuous start signal and continuous signal from differential pressure switch is mandatory for operating the timer (Only in model ST-15M2)
• Feedback outputs for timer healthy, timing in progress and power healthy available in model ST-6M2

Dimensions :

• Over-all: ST6-M1 / ST6-M2 / ST10-M2 / ST15-M2 / S1DC8-M3 – 200 x130 x 45mm
• ST4-M1: 110 x 86 x 68mm (W x H x D)
• ST10-M1 (IP) / ST10-M2 (IP) / ST6-M1 (IP) / ST6-M2 / ST15-M2 – 291 x 214 x 82mm (W x H x D)

Applications
Bag Filter systems, dust pollution systems, Air handling systems, MCC panels, conveyors, process industries, nitrogen and other gas plants, sewage water treatment plants, irrigation spraying systems and many more.

Features :

• LED indication for timing in progress
• Front protective cover for safety.
• Timer and base available for Track(except H3D1).
• Large transparent knob with lock is provided for precise time setting and protect from unintentional change of time setting.
• H1DA-X : Accepts any voltage from 12V AC/DC to 240V AC / 220V DC as signal between command contacts for timing initiation.
• H1D1-X, H3D1: Multifunction-On-Delay / Interval / Equal Cyclic-On / Equal Cyclic-Off programmable.

Applications : Textile machines, Vending machines and many more.

Dimensions :

• Over-all: 45 X 75 X 116mm (W X H X D).
• Cut-out: 46 X 46mm (W x H)

Features :

• Sleek, light weight, ABS enclosure
• Super bright, White color SMD, LED for fault indications
• Test / Mute / Acknowledge / Reset (buttons in front and terminals at rear) are available.
• Multiple units terminals can be connected in parallel to achieve more windows
• Each window can be programmed for fault inputs as NO or NC and output as alarm or trip
• Windows with different colours (Red, Green, Amber and White) can be supplied on request.
• Above program can be locked by removing the short link across specified terminals

Dimensions :

• Overall: M2-12, M2-16,M2-20, M2-24: 291 x 186.5 x 79mm (W x H x D)
• Cut-out: M2-12, M2-16,M2-20, M2-24: 285 x 181mm(W x H)

Applications
C & R panels, Transformer panels, DG set panels, Fire annunciation panels and Instrumentation panels etc.

Features :

• High brightness red LED display
• On site programmable CT(pri &sec) ratio
• Protection from dust and water as per IP-51 for front facia
• Measurement of basic parameters
• Program enable /disable facility available
• EMS-11: Measurement of current parameters (L-N) *CT primary and secondary programmable.
• EMS-12: Measurement of voltage parameters *PT primary and secondary programmable.
• EMS-13: Measurement of frequency parameter.
• EMS-14: Measurement of Power Factor parameter.
• EMS-18: VAF Meter with True RMS Sensing
• EMS-18: Measurement of basic parameters.(Current (L-N), Voltage (L-N),(L-L), frequency (average) and Power factor (Total) * CT ratio programmable, RS485 Mod-bus RTU protocol available, Sensing : True RMS.
• Hold/Scroll Facility available.

Dimensions :

• For EMS-11,EMS-12,EMS-13,EMS-14 Overall: 96 x 96 x 97.5mm (W x H x D) * Cutout : 92 x 92mm (W x H)
• For EMS-02,EMS-18 Overall: 96 x 96 x 117 mm (W x H x D) * Cutout : 92 x 92mm (W x H)

Applications
Sub metering, machines, Panels, power analysis systems etc.

Features :

• Aux. supply - wide voltage and frequency range.
• Compactable baud rate - 2400, 4800, 9600, 19200.
• Max. no of nodes - 32.
• Max. cable length (RS-232 side) - 15mtrs typical.
• Max. cable length (RS-485 side) - 1000mtrs typical.
• Mounting - Din-rail.
• LED indication for power, Receiving and Transmitting signals

Dimensions : Overall: 117 x 86 x 61mm (W x H x D)

Applications : Converts RS485 to RS232

Features :

• Micro Controller based 3 Channel DC Energy Meter
• Displays DC parameters V, I, KW, KWh ,MWh& Load on hours of all three channels.
• Displays the latest reading of all the cleared energies and load on hours.
• Display Hold / Scroll Facility available.
• Programmable Shunt ratios.
• Alphanumeric display for Parameter & values
• RS-485 serial port with Modbus RTU output.
• Wide Input Voltage and Current Range.
• Protection from dust and water as per IP-51.

Dimensions :

• Overall:96 x 96 x 117mm (W x H x D)
• Cutout: 92 x 92mm(W x H)

Applications
DC rectifier systems, Battery panels, DC distribution solar panels, DC loads, DC motors.

Features :

• Microcontroller based multifunction AC Energy Meter.
• Accuracy Class1.0 / (Class 0.5 calibration on Request).
• CT /PT (Pri/Sec) Programmable.
• Digital Measurement.
• IEC 62052-11 IEC 62053-21 IEC 62053-22 IEC 62053-23.
• RS 485 Serial Port with Modbus RTU Output.
• Flush / Panel Mounting.
• 96 x 96 mm DIN Mounting.
• Auto Scroll / Hold Facility.
• Internal Resettable fuse for protection of device against voltage fluctuations.
• Protection from dust and water as per IP-51.

Dimensions :

• Overall: 96 * 96 * 95.5mm (W x H x D)
• Cut-out: 92 * 92mm (W x H)

Applications
Sub metering panels, Distribution Panels, HT/ LT panels, DG panels etc.

Features :

• Measurement of basic, power, energy and demand parameters.
• On-site programmable PT and CT ratios.
• High brightness LED display (alpha numeric for parameter, numeric for value).
• Automatic CT reverse correction for energy and demand.
• Programmable demand techniques : block / sliding window.
• Programmable demand parameters : Apparent / Active power.
• Programmable demand range : Kilo / Mega.
• Programmable Alarm / hysterisis settings.
• Program RTC time to match EB meter's clock.
• For EMS-15C : Max. Demand Controller = Max. demand indicator + Relay module (4 relay) (RR-4).
• 4 control outputs for alarm and trip settings.

Dimensions :

• Overall : EMS 15,EMS 15C 96 x 96 x 117mm (W x H x D)
• RR-4 : 195x90x59mm(WxHxD) Cutout: 92 x 92mm(W x H)

Applications : In-comer distribution panels

Features :

• 31/2 digit, 7segment LED temperature display
• Wide voltage range (85-270V AC / DC)
• Universal input (J / K / PT-100)
• LED indication for sensor, funtion & relay status.
• Sensor and function lock.
• Dual function (On / Off or Self tuned).
• Single set point with relay output.
• Over voltage protection.
• H3TX-Ua / TX7-Ua / EX9-Ua/H3TX-U-RS : Single display for both process and set value.
• Temperature offset calibration user settable
• Single set point with relay output
• H3TX-2U / TX7-2U / EX9-2U : Dual display for process and set value.

Dimensions :

• Overall : H3TX Models 48 x 48 x 95.5mm, TX7 Models- 72 X 72 X 128mm; EX9 Models- 96 x 96 x 117mm (W x H X D)
• Cut-out : H3-TX Models – 46 x 46mm, TX7 Models - 69 x 69mm , EX9 Models – 92 x 92mm (W x H)

Applications : Furnace, Heat treatment equipment, Ovens, Boilers, Plastic and Rubber machinery and many more.

Features :

• Universal Input (J,K,PT-100) Selectable.
• Wide Voltage Range.
• ON / OFF or Self-Tuned Function Selectable.
• Single / double set point.
• Over Voltage Protection
• LED Indication for sensor selected, function and relay status
• Program enable / disable for sensor, function, hystersis, compensation features in TX7-Ua

Dimensions :

• Overall : 48 x 48 x 95.5mm, TX7 Models- 72 X 72 X 128mm; EX9 Models- 96 x 96 x 117mm (W x H X D)
• Cut-out : H3-TX Models – 46 x 46mm, TX7 Models - 69 x 69mm , EX9 Models – 92 x 92mm (W x H)

Applications
Any 3 phase 4wire systems like Motors, pumps, generators, Distribution panels, MCC, air conditioners, elevators, cranes and escalators etc.

Features :

• Battery operated (2nos x 1.5V DC, AA size) Real Time Clock in 24 hour format.
• Switches On and Off 4 times in a day with respect to real time

Dimensions : 110 X 86 X 68mm

Applications :  ATM air conditioners

Features :

• This is a light switch working on direct or reflective transmission principle.
• It consists of high intensity emitter source and high sensitive receiver
• The signal received from the receiver will operate a relay with ON delay or OFF delay depending on mode selected.
• The time range can be 0.3 sec / 30 sec.

Dimensions :

• EALS-4505 Dimension:45 x 75 x 116mm(WxHxD)
• EALSR-01:19.2 x 35.5 x 127.5mm (W x H x D)
• EALSE-01:19.2 x 35.5 x 127.5mm (W x H x D)

Applications : Hopper Feed Control, Stop Motion Device, Light Barriers, Level Control, Intrusion Alarm.

Features :

• Designed for the control of cotton level in laminae duct in ERM cleaners.
• Designed for Industrial Environment
• High Intensity pulsed Infra Red Emitter
• Time Delay up to 20 Seconds.
• Highly immune to Ambient Light
• 45mm Din Rail mounting.

Dimensions : Overall:45 x 75 x 116mm (W x H x D)

Applications : Designed for control of cotton level in laminae duct in ERM cleaners and similar application.

Features :

• Compact, light weight and SMPS design
• Versatile and easy snap-on mounting on Din-rail
• Very low ripple and noise
• Regulated and adjusted output
• Protection against over voltage, short circuit and over load.

Dimensions :

• Overall : MS-01 - 45 x 75 x 116mm, MS-02 – 110 x 86 x 71mm
• MS-03 - 155 x 88 x 79mm
• MS-04 - 172x150x78mm MS-05 – 22.5 x 75 x 97mm (W x H x D)

Applications : PLC, DC Panels, DC Solenoids, DC Relay boards, Battery Charging Panels.

Features :

• Micro-controller based design with world class Indian software.
• Non-contact sensing through reflected light beam on reflective sticker.
• LCD display
• Input sensing indication through LED.
• Memory facility to retain measured value.
• Portable, lightweight, strong and elegant ABS enclosure.
• Accuracy: 1RPM up to 5,000 RPM and 0.05% of the reading above 5,000 RPM.
• Resolution: 0.1RPM up to 5,999 RPM and 1RPM at and above 6,000RPM.
• Calibration certificate provided along with tachometer - traceable to national and international standards.

Dimensions : Over-all: 72 X 170 X 38mm (W X H X D).

Applications : Motors, Pumps, Generators, Engines and many more.

Features :

• Din sized enclosure for panel mounting.
• Wide Voltage range
• Front / Rear reset facility provided.
• Hold / Restart options (selectable) during power failure.
• Input signal from proximity switch ( NPN / PNP type) or Potential free (zero volt) signal from limit switch, relay o/p etc
• Over-voltage protection
• CT-5: Digital, single window 5 digit 7 segment red LED display with up counting for process value.
• Preset Counts can be programmed with the help of thumbwheel switch
• H3CT-5U : Digital, single window 5 digit 7 segment red LED display with up counting for both process value and set value
• Input sensitivity – programmable (1-100Hz)
• Internal Resettable fuse for protection of device against voltage fluctuations. Digital display will blink whenever voltage exceeds specified voltage range. Switch off the unit for sometime & then switch on when voltage returns to normal.

Dimensions : Overall: CT-5 – 72 x 72 x 128mm, H3CT-5U – 48 x 48 x 115mm (W x H x D)

Applications : Paper board counting, bag counting, bottle counting, relay change over counting, breaker panels, stroke counting in granite cutting m/c and many more.